Materiales de Construcción, Vol 60, No 299 (2010)

Shear friction capacity of recycled concretes


https://doi.org/10.3989/mc.2010.49708

B. González Fonteboa
Universidad de A Coruña, Spain

F. Martínez
Universidad de A Coruña, Spain

D. Carro
Universidad de A Coruña, Spain

J. Eiras
Universidad de A Coruña, Spain

Abstract


The aim of this research was to determine the behavior of recycled concrete in response to the phenomenon of shear transfer. To perform it, a conventional control concrete and a concrete with 50% recycled coarse aggregate were designed. An additional goal was to shed light on how this behavior is modified with a pozzolanic addition, silica fume. Therefore, two types of concrete were designed, a conventional and a recycled concrete, both made with 8% of silica fume.

In conclusion, a reduction of shear friction capacity was observed in recycled concretes, considerably higher in the case of the specimen without reinforcement. The addition of silica fume improved the behavior of recycled concretes.

The results obtained were compared with the formulations of the different authors. In all cases, these were found to be conservative. However, the safety margins offered by recycled concretes are lower than those obtained with conventional concretes.

Keywords


silica fume; recycled concrete; recycled aggregate; shear friction; strain

Full Text:


PDF

References


(1) Walraven, J. C.: “Fundamental Analysis of Aggregate Interlock”, ASCE, Journal of the StructuralDivision, vol. 107, ST11 (noviembre 1981), pp. 2245-2270.

(2) Peng, L.: Shear Strength of Beams by Shear-Friction, Tesis de la University of Calgary, Alberta, enero 1999, p. 164.

(3) Tozser, O.: Shear Analysis Using Shear Friction-size Effect and Prestressing, Tesis de la University of Calgary, Alberta, septiembre 1998, p. 193.

(4) Walraven J. C.: “High Performance Concrete: Exploring a new material”, Structural EngineeringInternational, vol. 5, nº 3 (agosto 1995), pp. 182-187.

(5) Walraven, J. C.: “Shear Friction in high Strength Concrete”, Progress in Concrete Research,Delft University of Technology, vol. 4 (marzo 1995), pp. 57-65.

(6) Birkeland, P. W., Birkeland, H. W.: “Connections in Precast concrete construction”, ACI Journal, vol. 63, nº 3 (marzo 1966), pp. 345-368.

(7) Raths, C. H.: Reader Comments on “Designs Proposals for Reinforced Concrete Corbels” by A.H. Mattock; PCI Journal, vol. 22, nº 2 (marzo-abril 1977), pp. 93-98.

(8) Shainkh, A. F.: “Proposed Revisions to Shear-Friction Provisions”, PCI Journal, vol. 23, nº 2 (marzo-abril 1978), pp. 12-21.

(9) Mattock, A. H.: “Shear Transfer in Concrete having reinforcement at an angle to the shear Plane”, ACI Special Publication, vol. 42 (enero 1974), pp. 17-42.

(10) Walraven, J. C.; Frenay, J.; Pruijssers, A.: “Influence of concrete strength and Load History on the Shear Friction Capacity of Concrete Members”, PCI Journal, vol. 32, nº 1 (1987), pp. 66-84.

(11) Mattock, A. H.: Reader Comments on “Influence of concrete strength and Load History on the Shear Friction Capacity of Concrete Members”, by J. C. Walraven, J. Frenay & A. Pruijssers, PCI Journal, vol. 33, nº 1 (enero-febrero 1988), pp. 165-166.

(12) Mau, S. T., Hsu, T. T. C.: Reader comments on “Influence of concrete strength and Load History on the Shear Friction Capacity of Concrete Members”, by J. C. Walraven, J. Frenay & A. Pruijssers, PCI Journal, vol. 33, nº 1 (enero-febrero 1988), pp. 166-168.

(13) Loov, R. E., Patnaik, A. K.: “Horizontal Shear Strength of Composite Concrete Beams with a Rough Interface”, PCI Journal, vol. 39, nº 1 (enero-febrero 1994), pp. 48-69.

(14) EHE. Instrucción de Hormigón Estructural. Publicaciones del Ministerio de Fomento. Secretaría General Técnica.

(15) Ravindrarajah, R. S.; Tam, C. T.: “Methods of Improving the Quality of Recycled Aggregate Concrete”; Demolition and Reuse of Concrete and Masonry, vol. 2 Reuse of Demolition Waste, Proceedings of the Second International RILEM Symposium, Ed. Y. Kasai; (noviembre 1988), pp 575-584, ISBN 0-412-32110-6.

(16) Banta, T. E.: Horizontal Shear Transfer Between Ultra High Performance Concrete and Lightweight concrete, p. 130, thesis submitted to the faculty of the Virginia Polytechnic Institute, febrero 2005.

(17) Hwang, S. J.; Yu, H. W.; Lee, H. J.: “Theory of interface shear capacity of reinforced concrete”, Journal of Structural Engineering, vol. 126, nº 6 (junio 2000), pp. 700-707. doi:10.1061/(ASCE)0733-9445(2000)126:6(700)

(18) Ibell, T.; Burgoyne, C.: “Use of fiber-reinforced plastics versus steel for shear reinforcement of concrete”, ACI Structural Journal, vol. 96, nº 6 (noviembre-diciembre 1999), pp. 997-1002.

(19) Balaguru, P.; Dipsia, M. G.: “Properties of fiber reinforced high-strength semilightweight concrete”, ACI Materials Journal, vol. 90, nº 5 (septiembre-octubre 1993), pp. 399-405.

(20) Duthinh, D.; Carino, N. J.: Shear design of high-strength concrete beams: a review of the state-of-the art, p. 198, en Report NISTIR 5870, Building and Fire Research Laboratory, National Institute of Standards and Technology, agosto 1996.

(21) Duthinh, D.: “Sensitivity of shear strength of reinforced concrete and prestressed concrete beams to shear friction and concrete softening according to modified compression field theory”, ACI Structural Journal, vol. 96, nº 4 (julio-agosto 1999), pp. 495-508.

(22) Mohamed, A.; Richard, N.: “Enhanced contact model for shear friction of normal and high-strength concrete”, ACI Structural Journal, vol. 96, nº 3 (mayo-junio 1999), pp. 348-360.

(23) Ince, R.; Yalcin, E.; Arslan, A.: “Size-dependent response of dowel action in R.C. members”; Engineering Structures, vol. 29 (2007), pp. 955-961. doi:10.1016/j.engstruct.2006.07.006

(24) Menkulasi, F.: Horizontal Shear Connectors for Precast Prestressed Bridge Deck Panels, p. 138, thesis submitted to the faculty of the Virginia Polytechnic Institute; agosto 2002.

(25) Rahal, K.: “Mechanical properties of concrete with recycled coarse aggregate”, Building and Environmental,vol. 42, nº 1 (enero 2005), pp. 407-415.

(26) Hendriks, Ch. F.; Pietersen, H. S.; Fraay, A. F. A.: “Recycling of Buildings and Demolition Waste – An Integrated approach”. Use of Recycled Concrete Aggregate, Sustainable Construction; Ed. Dhir, Henderson y Limbachiya; pp. 419-432, 1998, ISBN 0-7277-2726-5.

(27) Carrasquillo, R. L.; Slate, F. O.; Nilson, A. H.: “Properties of High Strength Concrete Subject to Short - term Loading”, ACI journal, vol. 78, nº 3 (mayo-junio 1981), pp. 171-178.

(28) Hansen, T. C.; Narud, H.: “Strength of Recycled Concreted Made from Crushed Concrete Coarse Aggregate”; Concrete International, vol. 5, nº 1 (enero 1983), pp. 79-83.

(29) Comisión 2. Grupo de trabajo 2/5 “Hormigón Reciclado”: Utilización de árido reciclado para la fabricación de hormigón estructural, p. 189, Ed. ACHE (Asociación Científico-técnica del Hormigón Estructural), España, 2006. ISBN 84-89670-55-2.




Copyright (c) 2010 Consejo Superior de Investigaciones Científicas (CSIC)

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.


Contact us materconstrucc@ietcc.csic.es

Technical support soporte.tecnico.revistas@csic.es