Study of Mechanical Characterization of Ceramic Specimens from a Brazilian Test Adaptation
DOI:
https://doi.org/10.3989/mc.2011.55809Keywords:
Ceramic, Pressing, Brazilian testAbstract
The Brazilian Test is easy to perform and its result is the tensile strength of the material provided certain ratios are fulfilled between the diameter of the sample, the load bearing width and the characteristic length of the material. In this paper we present experimental results obtained from 8 mm-thick ceramic cylinders whose diameter was 40 mm in length. The cylinders were obtained from a standard type of clay by pressing and subsequent baking at 900 ºC. We made a complete mechanical characterization of the material, which included obtaining fracture properties, and a numerical simulation of the Brazilian test based on the cohesive crack model. Numerical results confirm that the size and boundary conditions chosen for the test are adequate to get the actual tensile strength of construction ceramics, which prove that this type of test is useful to compare the strength of several types of construction ceramics in a simple and convenient way. Besides, it requires a very small amount of material to prepare the specimen
Downloads
References
(1) Rocco, C., Guinea, G.V., Planas, J., Elices, M.: "Review of the splitting-test standards from a fracture mechanics point of view", Cement and Concrete Research, 31(1) (2001), pp. 73-82. doi:10.1016/S0008-8846(00)00425-7
(2) Rocco, C., Guinea, G.V., Planas, J., Elices, M.: "Size effect and boundary conditions in the brazilian test: Theoretical analysis", Materials and Structures, 32 (220) (1999), pp. 437-444. doi:10.1007/BF02482715
(3) Rocco, C., Guinea, G.V., Planas, J., Elices, M.: "Size effect and boundary conditions in the Brazilian test: Experimental verification", Materials and Structures 32 (217), (1999), pp. 210-217. doi:10.1007/BF02481517
(4) Rocco, C., Guinea, G.V., Planas, J., Elices, M.: "Mechanisms of rupture in splitting tests", ACI Materials Journal 96(1), (1999), pp.52-60.
(5) Ruiz, G.: "Propagation of a cohesive crack crossing a reinforcement layer", International Journal of Fracture 111, (2001), pp.265-282. doi:10.1023/A:1012260410704
(6) Acosta, A., Iglesias, I., Aineto, M., Romero, M., Rincón, J.Ma.: "Utilisation of IGCC slag and clay steriles in soft mud bricks (by pressing) for use in building bricks manufacturing", Waste Management, 22, (2002), pp.887-891. doi:10.1016/S0956-053X(02)00075-2
(7) Guinea, G.V., Elices, M., Planas, J.: "Measurement of the fracture energy using 3-point bend tests. 1. Influence of experimental procedures", Materials and Structures 25(148), (1992), pp. 212-218. doi:10.1007/BF02473065
(8) Planas, J., Elices, M., Guinea, G.V.: "Measurement of the fracture energy using 3-point bend tests. 2. Influence of bulk energy dissipation" Materials and Structures 25(149), (1992), pp. 305-312. doi:10.1007/BF02472671
(9) Elices, M., Guinea, G.V., Planas, J.: "Measurement of the fracture energy using 3-point bend tests. 3. Influence of cutting the P-× tail" Materials and Structures 25(150), (1992), pp. 327-334. doi:10.1007/BF02472591
(10) Tada, H., Paris, P., Irwin, G.R.: The stress analysis of cracks handbook, Second edition, Paris Production Inc. and Del Research Corp., St. Louis, Missouri, USA, (1985).
(11) Yu, R.C., Ruiz, G., Pandolfi, A.: "Numerical investigation of the dynamic behavior of advanced ceramics." Engineering Fracture Mechanics 71(4-6), (2004) pp. 897-911. doi:10.1016/S0013-7944(03)00016-X
(12) Vekinis, B., Ashby, M.G., Beaumont, P.W.R.: "R-curve behavior of Al2O3 ceramics", Acta Metallurgica et Materialia, 38(6) (1990), pp.1151-1162. doi:10.1016/0956-7151(90)90188-M
(13) Bower, A.F., Ortiz, M.: "A three-dimensional analysis of crack trapping and bridging by tough particles", Journal of the Mechanics and Physics of Solids, 39(6) (1991), pp. 815-858. doi:10.1016/0022-5096(91)90026-K
(14) (14) Kobayashi, A.S.: "Dinamic fracture of ceramics and ceramic composites", Materials Science and Engineering, A143 (1991), pp. 111-117. doi:10.1016/0921-5093(91)90730-B
(15) Guo, Z.K., Kobayashi, A.S., Hay, J.C., White, K.W.: "Fracture process zone modeling of monolithic Al2O3", Engineering Fracture Mechanics, 63 (1999), pp. 115-129. doi:10.1016/S0013-7944(99)00030-2
(16) Tran, D.K., Kobayashi, A.S., White, K.W.: "Process zone of polycrystalline alumina", Experimental Mechanics, 39(1) (1999), pp. 20-24. doi:10.1007/BF02329296
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2011 Consejo Superior de Investigaciones Científicas (CSIC)
This work is licensed under a Creative Commons Attribution 4.0 International License.
© CSIC. Manuscripts published in both the printed and online versions of this Journal are the property of Consejo Superior de Investigaciones Científicas, and quoting this source is a requirement for any partial or full reproduction.All contents of this electronic edition, except where otherwise noted, are distributed under a “Creative Commons Attribution 4.0 International” (CC BY 4.0) License. You may read here the basic information and the legal text of the license. The indication of the CC BY 4.0 License must be expressly stated in this way when necessary.
Self-archiving in repositories, personal webpages or similar, of any version other than the published by the Editor, is not allowed.
