Predicting the density of structural timber members in service. The combine use of wood cores and drill resistance data

Authors

  • M. J. Morales-Condea Universidad de Sevilla
  • C. Rodríguez-Liñán Universidad de Sevilla
  • J. Saporiti-Machado Laboratório Nacional de Engenharia Civil

DOI:

https://doi.org/10.3989/mc.2014.03113

Keywords:

Timber, Density, Resistograh, Wood core, Structures in service, Mechanical Properties

Abstract


Drilling devices is used to get information about the cross-section properties and internal defects of structural members. Drill resistance is correlated with density which is often used to predict the mechanical properties of timber elements. However in situ a regression curve cannot be obtained and pre-existent curves provides unreliable predictions. The present paper proposes a procedure for in situ “calibration” of drill resistance data. The “calibration” is based on density values from wood cores taken in the close vicinity of drill holes. Two approaches were tested. One approach based on a regression curve built using wood cores density and drill resistance values obtained from a limited number of members. The other approach uses the information of one wood core to “calibrate” the drill resistance profile taken at the same member. Following this procedure a density prediction is obtained showing a low mean percentage error and a medium coefficient of determination.

Downloads

Download data is not yet available.

References

1. Calderoni, C.; De Matteis, G.; Giubileo, C.; Mazzolani, F.M. (2009). Experimental correlations between destructive and non-destructive tests on ancient timber elements. Engineering Structures, 32[2], 442–448. http://dx.doi.org/10.1016/j.engstruct.2009.10.006

2. Rinn, F.; Schweingruber, F-H.; Schär, E. (1996) Resistograph and X-ray density charts of wood. Comparative evaluation of drill resistance profiles and X-ray density charts for different wood species. Holzforschung, 50[4], 303–311. http://dx.doi.org/10.1515/hfsg.1996.50.4.303

3. Fernadez-Golfin Seco, J.I.; Barra, M.R.D. (1996) Growth rate as predictor of density and mechanical quality of sawn timber from fast growing species. Holz als Roh- und Werkstoff, 54, 171–174. http://dx.doi.org/10.1007/s001070050161

4. Kasal, B.; Tannert, T. (Editors) (2011) In-situ assessment of timber. RILEM State of the Art Reports, Vol. 7. Springer Verlag.

5. Lourenço, P.; Feio, A.; Machado, J.S. (2007) Chestnut wood in compression perpendicular to the grain: Non-destructive correlations for test results in new and old wood. Construc. Build. Mat. 21, 1617–1627. http://dx.doi.org/10.1016/j.conbuildmat.2006.07.011

6. Brashaw, B.; Vatalaro, R.; Ross, R.J.; Wang, X.; Schmieding, S.; Okstad, W. (2011) Historic log cabin structural condition assessment and rehabilitation – A case study. In: Ferenc Divos (ed) 17th International Nondestructive Testing and Evaluation of Wood Symposium, 505–512.

7. Henriques, D.; Nunes, L.; Machado, J.S.; Brito, J. (2011) Timber in Buildings: Estimation of Some Properties using Pilodyn and Resistograph. Procc. International Conference on Durability of Building Materials and Components. Porto, Portugal.

8. Lear, G.; Kasal, B.; Anthony, R. (2010) Resistance drilling. Bohumil Kasal and Thomas Tannert (Eds) In: In situ Assessment of Structural Timber. RILEM State of the Art Reports. Springer, 51–57.

9. Tannert, T. (2010) Drill resistance. Phillip Dietsch and Jochen Köhler (Eds) In: Assessment of timber structures. COST E 55 report. Shaker Verlag, 72–74.

10. Ceraldi, C.; Mormone, V.; Russo-Ermolli, E. (2001) Resistographic inspection of ancient timber structures for the evaluation of mechanical characteristics. Materials and Structures, 34, 59–64. http://dx.doi.org/10.1007/BF02482201

11. Gantz, C.H. (2002) Evaluating the efficiency of the Resistograph to estimate genetic parameters for wood density in two softwood and two hardwood species. Master's Thesis, Faculty of North Carolina State University.

12. Lin, C.J.; Wang, S.Y.; Lin, F.C.; Chiu, C.M. (2003) Effect of moisture content on the drill resistance value in taiwania plantation wood. Wood and Fiber Science, 35, 234–238.

13. Tseng, Y.J.; Hsu, M.F. (2008) Evaluating the Mechanical Properties of Wooden Components Using Drill Resistance Method. Procc 10th World Conference on Timber Engineering, 303–310. Singapore.

14. Lee Jun-Jae (2004) Reliability analysis of deteriorated post member. Procc 8th World Conference on Timber Engineering, 223–228.

15. Kasal, B.; Anthony, R.W. (2004) Advances in in situ evaluation of timber structures. Progress in Structural Engineering and Materials, 6, 94–103. http://dx.doi.org/10.1002/pse.170

16. Piazza, M.; Riggio, M. (2008) Visual strength-grading and NDT of timber in traditional structures. Journal of Building Appraisal, 3, 267–296. http://dx.doi.org/10.1057/jba.2008.4

17. Zhang, H.; Wang, X.; Zhu, L.; Ross, R.J.; Brashaw, B.K. (2011) An integrated NDT approach for determinaning residual strength of ancient wood structural members. 17th International Nondestructive Testing and Evaluation of Wood Symposium, 547–554. Ferenc Divos (ed).

18. Ramos, L.; Lourenço, P.B. (2004) Modeling and vulnerability of historical city centers in seismic areas: a case study in Lisbon. Engineering Structures, 26, 1295–1310. http://dx.doi.org/10.1016/j.engstruct.2004.04.008

19. Machado, J.S.; Cruz, H. (1997) Assessment of timber structures. Determination of density profile by non-destructive methods. Revista Portuguesa de Engenharia de Estruturas 42, 15–18.

20. Johnstone, D.; Tausz, M.; Moore, G.; Nicolas, M. (2010) Quantifying wood decay in Sidney bluegum (Eucalyptus saligna) trees. Arboriculture & Urban Forestry 36 [6], 243–252.

21. ASTM standard D2395-07a (2007) Standard Test Methods for Specific Gravity of Wood and Wood-Based Materials. ASTM International, West Conshohocken.

22. EN 13183-1:2002. (2002) Contenido de humedad de una pieza de madera aserrada- Parte1: Determinación por el método de secado en estufa.

23. R version 2.13.1 (2011) The R Foundation for Statistical Computing JCSS Probabilistic Code.

24. Grippa, M.R.; Faggiano, B.; Marzo, A.; Mazzolani, F.M. (2010) Combined methods for in situ mechanical identification of ancient timber structures based on non-destructive tests. 11th World Conference on Timber Engineering. Ario Ceccotti and Jan-Willem van de Kuilen (Eds).

Published

2014-09-30

How to Cite

Morales-Condea, M. J., Rodríguez-Liñán, C., & Saporiti-Machado, J. (2014). Predicting the density of structural timber members in service. The combine use of wood cores and drill resistance data. Materiales De Construcción, 64(315), e029. https://doi.org/10.3989/mc.2014.03113

Issue

Section

Research Articles